List of international Standards (Procedures and Components)
PROCEDURES (Looking for an specific document use database routines.)
| Procedures for temperature and irradiance corrections to measured I-V characteristics of crystalline silicon photovoltaic devices |
|||
| Amendment No. 1 |
|||
| Photovoltaic devices. Part 1: Measurement of photovoltaic current-voltage characteristics |
|||
| Photovoltaic devices. Part 2: Requirements for reference solar cells |
|||
| Amendment 1 |
|||
| Photovoltaic devices. Part 3: Measurement principles for terrestrial photovoltaic (PV) solar devices with reference spectral irradiance data |
|||
| Photovoltaic devices - Part 5: Determination of the equivalent cell temperature (ECT) of photovoltaic (PV) devices by the open-circuit voltage method |
|||
| Photovoltaic devices - Part 6: Requirements for reference solar modules |
|||
| Amendment 1 |
|||
| Photovoltaic devices - Part 7: Computation of spectral mismatch error introduced in the testing of a photovoltaic device |
|||
| Photovoltaic devices - Part 8: Measurement of spectral response of a photovoltaic (PV) device |
|||
| Photovoltaic devices - Part 9: Solar simulator performance requirements |
|||
| Photovoltaic devices - Part 10: Methods of linearity measurement |
|||
| Overvoltage protection for photovoltaic (PV) power generating systems - Guide |
|||
| Characteristic parameters of stand-alone photovoltaic (PV) systems |
|||
| Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval |
|||
| Terrestrial photovoltaic (PV) power generating systems - General and guide |
|||
| UV test for photovoltaic (PV) modules |
|||
| Thin-film terrestrial
photovoltaic (PV) modules - Design qualification and type approval |
|||
| Photovoltaic systems - Power conditioners - Procedure for measuring efficiency |
|||
| Salt mist corrosion testing of photovoltaic (PV) modules |
|||
| Rating of direct coupled photovoltaic (PV) pumping systems |
|||
| Susceptibility of a photovoltaic (PV) module to accidental impact damage (resistance to impact test) |
|||
| Photovoltaic system performance
monitoring - Guidelines for |
|||
| Analytical expression
for daily solar profiles |
|||
| Photovoltaic (PV) systems - Characteristics of the utility interface |
|||
| Crystalline silicon photovoltaic (PV) array - On-site measurement of I-V characteristics |
|||
| Solar photovoltaic energy systems - Terms and symbols |
|||
| Specifications
for the use of renewable energies in rural |
|||
Information from IEC Web Page: www.iec.ch
Last Update: 4 January 2002
COMPONENTS
Looking for an specific component use database routines.
| IEC 61044 Ed. 1.0 |
Opportunity-charging of lead-acid traction batteries |
| IEC 61056-1 Ed. 1.0 |
Portable lead-acid cells and batteries (Valve regulated types) - Part 1: General requirements, functional characteristics - Methods of test |
| IEC 61056-2 Ed. 1.0 |
Portable lead-acid cells and batteries (Valve regulated types) - Part 2: Dimensions, terminals and marking |
| IEC 61056-3 Ed. 1.0 |
Portable lead-acid cells and batteries (Valve-regulated types) - Part 3: Safety recommendations for use in electric appliances |
| IEC 60254-1 Ed. 3.0 |
Lead-acid traction batteries - Part 1: General requirements and methods of test |
| IEC 60254-2 Ed. 3.0 |
Lead-acid traction batteries - Part 2: Dimensions of cells and terminals and marking of polarity on cells |
| IEC 60896-1 (1987-01) |
Stationary lead-acid batteries - General requirements and methods of test. Part 1: Vented types. |
| IEC 60896-1 Amd.1 Ed. 1.0 |
Amendment No. 1 |
| IEC 60896-1 Amd.2 Ed. 1.0 |
Amendment No. 2 |
| IEC 60896-1 Ed. 1.0 |
Stationary lead-acid batteries - General requirements and methods of test. Part 1: Vented types |
| IEC 60896-1-am1 (1988-01) |
Amendment No. 1 |
| IEC 60896-1-am2 (1990-12) |
Amendment No. 2 |
| IEC 60896-2 (1995-11) |
Stationary lead-acid batteries - General requirements and test methods - Part 2: Valve regulated types. |
| IEC 60896-2 Ed. 1.0 |
Stationary lead-acid batteries - General requirements and test methods - Part 2: Valve regulated types |
| IEC 60095-1 Ed. 5.0 |
Lead-acid starter batteries. Part 1: General requirements and methods of test |
| IEC 60095-2 Amd.1 Ed. 3.0 |
Amendment No. 1 |
| IEC 60095-2 Amd.2 Ed. 3.0 |
Amendment No. 2 |
| IEC 60095-2 Ed. 3.0 |
Lead-acid starter batteries. Part 2: Dimensions of batteries and dimensions and marking of terminals |
| IEC 60095-4 Amd.1 Ed. 1.0 |
Amendment No. 1 |
| IEC 60095-4 Ed. 1.0 |
Lead-acid starter batteries. Part 4: Dimensions of batteries for heavy trucks |
| IEC 60952-1 (1988-07) |
Aircraft batteries. Part 1: General test requirements and performance levels. |
| IEC 60952-1 Ed. 1.0 |
Aircraft batteries. Part 1: General test requirements and performance levels |
| IEC 60952-2 (1991-03) |
Aircraft batteries - Part 2: Design and construction requirements |
| IEC 60952-2 Ed. 1.0 |
Aircraft batteries - Part 2: Design and construction requirements |
| IEC 60952-3 (1993-07) |
Aircraft batteries - Part 3: External electrical connectors. |
| IEC 60952-3 Ed. 1.0 |
Aircraft batteries - Part 3: External electrical connectors |
| IEC 60610 (1978-01) |
Principal aspects of functional evaluation of electrical insulation systems: Aging mechanisms and diagnostic procedures. |
| IEC 60611 (1978-01) |
Guide for the preparation of test procedures for evaluating the thermal endurance of electrical insulation systems. |
| IEC 60614-1 (1994-03) |
Conduits for electrical installations - Specification - Part 1: General requirements. |
| IEC 60614-1-am1 (1995-09) |
Amendment No. 1 |
| IEC 60614-2-1 (1982-01) |
Specification for conduits for electrical installations. Part 2: Particular specifications for conduits. Section One: Metal conduits. |
| IEC 60614-2-1-am1 (1993-10) |
Amendment No. 1 |
| IEC 60614-2-5 (1992-11) |
Specifications for conduits for electrical installations - Part 2: Particular specifications for conduits - Section 5: Flexible conduits. |
| IEC 60811-1-1 (1993-10) |
Common test methods for insulating and sheathing materials of electric cables - Part 1: Methods for general application -Section 1: Measurement of thickness and overall dimensions - Tests for determining the mechanical properties. |
| IEC 60811-1-2 (1985-07) |
Common test methods for insulating and sheathing materials of electric cables - Part 1: Methods for general application - Section Two: Thermal aging methods. |
| IEC 60811-1-2-am1 (1989-11) |
Amendment No. 1 |
| IEC 60811-1-4 (1985-07) |
Common test methods for insulating and sheathing materials of electric cables - Part 1: Methods for general application - Section Four: Test at low temperature. |
| IEC 60811-1-4-am1 (1993-08) |
Amendment No. 1 |
| EC 60811-4-1 (1985-10) |
Common test methods for insulating and sheathing materials of electric cables - Part 4: Methods specific to polyethylene and polypropylene compounds - Section One - Resistance to environmental stress cracking - Wrapping test after thermal aging in air - M |
| IEC 60811-4-1-am2 (1993-08) |
Amendment No. 2 |
| IEC 60812 (1985-07) |
Analysis techniques for system reliability - Procedure for failure mode and effects analysis (FMEA). |
| IEC 60998-1 (1990-05) |
Connecting devices for low voltage circuits for household and similar purposes. Part 1: General requirements. |
| IEC 60998-2-1 (1990-05) |
Connecting devices for low voltage circuits for household and similar purposes. Part 2-1: Particular requirements for connecting devices as separate entities with screw-type clamping units. |
| IEC 60998-2-2 (1991-11) |
Connecting devices for low-voltage circuits for household and similar purposes - Part 2-2: Particular requirements for connecting devices as separate entities with screwless-type clamping units. |
| IEC 60998-2-3 (1991-11) |
Connecting devices for low-voltage circuits for household and similar purposes - Part 2-3: Particular requirements for connecting devices as separate entities with insulation piercing clamping units. |
| IEC 60998-2-4 (1993-05) |
Connecting devices for low-voltage circuits for household and similar purposes - Part 2-4: Particular requirements for twist-on connecting devices. |
| IEC 60998-2-5 (1996-01) |
Connecting devices for low-voltage circuits for household and similar purposes - Part 2-5: Particular requirements for connecting boxes (junction and/or tapping) for terminals or connecting devices. |
| IEC 60439-1 (1992-12) |
Low-voltage switchgear and controlgear assemblies - Part 1: Type-tested and partially type-tested assemblies. |
| IEC 60439-1-am1 (1995-11) |
Amendment No. 1 |
| IEC 60439-1-am2 (1996-12) |
Amendment No. 2 |
| IEC 60439-2 (1987-11) |
Low-voltage switchgear and controlgear assemblies. Part 2: Particular requirements for busbar trunking systems (busways). |
| IEC 60439-2-am1 (1991-09) |
Amendment No. 1 |
| IEC 60439-3 (1990-12) |
Low-voltage switchgear and controlgear assemblies. Part 3: Particular requirements for low-voltage switchgear and controlgear assemblies intended to be installed in places where unskilled persons have access for their use - Distribution boards. |
| IEC 60439-3-am1 (1993-10) |
Amendment No. 1 |
| IEC 60439-4 (1990-12) |
Low-voltage switchgear and controlgear assemblies. Part 4: Particular requirements for assemblies for construction sites (ACS). |
| IEC 60439-4-am1 (1995-12) |
Amendment No. 1 |
| IEC 60439-5 (1996-03) |
Low-voltage switchgear and controlgear assemblies - Part 5: Particular requirements for assemblies intended to be installed outdoors in public places - Cable distribution cabinets (CDCs) for power distribution in networks. |
| IEC 60529 (1989-11) |
Degrees of protection provided by enclosures (IP Code). Applies to the classification of degrees of protection provided by enclosures for electrical equipment with a rated voltage not exceeding 72,5 kV. Has the status of a basic safety publication. |
| IEC 61204 (1993-02) |
Low-voltage power supply devices, d.c. output - Performance characteristics and safety requirements. |
| IEC 60146-1-1 (1991-04) |
General requirements and line commutated convertors - Part 1-1: Specifications of basic requirements. |
| IEC 60146-1-1-am1 (1996-07) |
Amendment No. 1 to IEC 146-1-1. |
| IEC 60146-1-2 (1991-04) |
General requirements and line commutated convertors - Part 1-2: Application guide. |
| IEC 60146-1-3 (1991-04) |
General requirements and line commutated convertors - Part 1-3: Transformers and reactors. |
| IEC 60400 (1996-06) |
Lampholders for tubular fluorescent lamps and starterholders. |
| IEC 60400-am1 (1997-04) |
Amendment No. 1 |
| IEC 60598-1 (1996-12) |
Luminaires - Part 1: General requirements and tests |
| IEC 60598-2-1 (1979-01) |
Luminaires. Part 2: Particular requirements. Section One: Fixed general purpose luminaires. |
| IEC 60598-2-1-am1 (1987-01) |
Amendment No. 1 |
| IEC 60598-2-23 (1996-04) |
Luminaires - Part 2: Particular requirements - Section 23: Extra low voltage lighting systems for filament lamps. |
| IEC 60598-2-3 (1993-04) |
Luminaires - Part 2: Particular requirements - Section 3: Luminaires for road and street lighting. |
| IEC 60598-2-3-am1 (1997-04) |
Amendment No. 1 |
| IEC 60598-2-4 (1997-04) |
Luminaires - Part 2: Particular requirements - Section 4: Portable general purpose luminaires |
| IEC 60598-2-5 (1979-01) |
Luminaires. Part 2: Particular requirements. Section Five: Floodlights. |
| IEC 60598-2-5-am1 (1987-01) |
Amendment No. 1 |
| IEC 60598-2-5-am2 (1993-04) |
Amendment No. 2 |
| IEC 60598-2-7 (1982-01) |
Luminaires. Part 2: Particular requirements. Section Seven: Portable luminaires for garden use. |
| IEC 60598-2-7-am1 (1987-01) |
Amendment No. 1 |
| IEC 60598-2-7-am2 (1994-08) |
Amendment No. 2 |
| IEC 60598-2-8 (1996-07) |
Luminaires- Part 2: Particular requirements - Section 8: Handlamps. |
| IEC 60081 (1984-01) |
Tubular fluorescent lamps for general lighting service. |
| IEC 60081-am1 (1987-01) |
Amendment No. 1 |
| IEC 60081-am2 (1988-01) |
Amendment No. 2 |
| IEC 60081-am3 (1992-07) |
Amendment No. 3 |
| IEC 60081-am4 (1993-09) |
Amendment No. 4 |
| IEC 60081-am5 (1994-12) |
Amendment No. 5 |
| IEC 60810 (1993-10) |
Lamps for road vehicles - Performance requirements. |
| IEC 60810-am1 (1994-07) |
Amendment No. 1 |
| IEC 60924 (1990-07) |
D.C. supplied electronic ballasts for tubular fluorescent lamps - General and safety requirements. |
| IEC 60924-am1 (1993-03) |
Amendment No. 1 |
| IEC 60925 (1989-06) |
D.C. supplied electronic ballasts for tubular fluorescent lamps - Performance requirements. |
| IEC 60925-am1 (1996-05) |
Amendment No.1 |
| IEC 60095-1 Amd.1 Ed. 5.0 |
Amendment No. 1 |
| IEC 60095-1 Amd.2 Ed. 5.0 |
Amendment No. 2 |
| IEC 61162-1 (1995-`11) |
Maritime navigation and radio communication equipment and systems - Digital interfaces - Part 1: Single talker and multiple listeners. Contains the requirements for data communication between maritime electronic instruments, navigation and radio communication. |